亚洲色偷偷综合亚洲AV伊人蜜桃_最近免费看av_国产人妻午夜在线无码_国语FREE性XXXXXHD_高清做爰免费无遮网站挡_国产精品呻吟AV久久高潮

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

self-locking hydraulic cylinder Sold to Sudan

Release time:2023-11-16 08:44:32 Hits: Current position: Home > News

This article mainly introduces:

Sudan hydraulic cylinder,self-locking hydraulic cylinder manufacturer,self-locking hydraulic cylinder

Sudan self-locking hydraulic cylinder

(Sudan self-locking hydraulic cylinder,produced by Hebei Hengyu company)

self-locking hydraulic cylinder are widely used in Sudan,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed self-locking hydraulic cylinder for customers from Sudan.

Introduction to self-locking hydraulic cylinder:

When the long-stroke self-locking hydraulic cylinder rotates horizontally, the piston rod bends due to its own weight, causing the guide sleeve and piston to produce biased load, resulting in self-locking hydraulic cylinder head seal damage, oil leakage, and piston sleep in the self-locking hydraulic cylinder. The following measures can be taken: increase the piston plan to adjust the piston outer circle and process it into a convex drum, so that the piston can self-position, improve the force situation, and reduce and avoid pulling the self-locking hydraulic cylinder; The piston and the piston rod are connected with a spherical joint.

self-locking hydraulic cylinder head explanation: low pressure castings, medium and low pressure with HT300 gray iron, medium and high pressure with 35, 45 steel. When the self-locking hydraulic cylinder head itself is the guide sleeve of the piston rod, the self-locking hydraulic cylinder head is best cast iron. At the same time, brass, bronze or other wear-resistant materials should be fused on the guide surface. If the guide sleeve is pressed into the self-locking hydraulic cylinder head, the guide sleeve shall be wear-resistant cast iron, bronze or brass.

When the self-locking hydraulic cylinder is installed, the piston and the self-locking hydraulic cylinder head and other parts have large mass, large size and large inertia, even if there is a lifting equipment auxiliary installation, because the specified clearance is small, no matter how hard it will be put into, therefore, the end of the piston or the self-locking hydraulic cylinder head boss is easy to cause scars when it hits the inner surface of the self-locking hydraulic cylinder wall. The solution to this problem: for a large number of small products, the use of autocratic assembly oriented tools during installation; For heavy, thick and large large and medium-sized self-locking hydraulic cylinders, only careful and careful operation can be avoided.

self-locking hydraulic cylinder use should try to avoid sealing belt into the self-locking hydraulic cylinder. As a simple sealing material, polytetrafluoroethylene plastic sealing tape is often used in installation and inspection, and if the winding method of the linear and ribbon-shaped sealing material is wrong, the sealing tape will be cut off and enter the self-locking hydraulic cylinder. The wire belt seal will not have any effect on the winding of the sliding part, but it will cause the check valve of the self-locking hydraulic cylinder to fail to operate or the buffer regulating valve can not be adjusted to the end. For the circuit, it may cause the action of the reversing valve, the relief valve and the reducing valve to fail.

Answers to some questions about self-locking hydraulic cylinder:

PLC+ inverter + motor + pump + solenoid valve + cylinder combination, can control the accuracy of cylinder position?
In the case of extremely high accuracy requirements, you can not, please consider a few problems: 1, hydraulic oil can be compressed, it is elastic like a spring. Therefore, in the general hydraulic servo system, the valve control is far more accurate than the pump control. Because the valve can be installed very close to the hydraulic cylinder, or even installed on the hydraulic cylinder, but the pump must go through the tubing and then into the hydraulic cylinder, there is a long distance, which greatly reduces the rigidity of the system and increases the difficulty of control. 2, the quantitative pump is first of all leaking, and there is 10%-20% flow pulsation. Secondly, and more unfortunately, the leakage of the pump is related to the pressure and is non-linear.

How big is the pump and motor for 20 tons of hydraulic cylinder?
According to the working pressure of 25 mpa estimate, the cylinder should use 100mm bore, 63mm piston rod, stroke 40mm. According to 30 reciprocating calculation, the flow rate is about 25 liters/minute. The motor power is 11 kW, want to be cheap, use 25SCY14-1B oil pump can be.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
主站蜘蛛池模板: 亚洲伊人色欲综合网无码 | 国产精品人妻久久久久 | 久久久国产精品厨房 | 四虎永久在线精品免费AV | 日日碰狠狠躁久久躁孕妇 | 成人VA亚洲VA欧美天堂 | 国模无码一区二区三区 | 大地资源网更新免费播放视频 | 国产传媒在线免费观看 | 最近更新中文字幕手机版 | 熟女体下毛毛黑森林 | 亚洲中文字幕无码久久 | 国产成人无码久久久精品一 | 被男人嗦过奶头一下就变大了 | 爱性久久久久久久久 | 国产一卡2卡三卡4卡免费网站 | 日产无码精品一区二区三区 | 伊人色综合久久天天五月婷 | 欧美巨大XXXX做受中文字幕 | 超清无码av丝袜片在线观看 | 涩涩视频在线观看 | 一本色道无码道DVD在线观看 | 中文字幕11页中文字幕11页 | 男女无遮挡XX00动态图120秒 | 日本系列_7777ih_1页 | 欧美精品一区二区三区制服首页 | 忘忧草社区www日本高清图片 | 被老师叫到办公室跪着打手心 | 日本黄页网站免费大全1688 | 少妇一晚三次一区二区三区 | 国产成A人亚洲精V品无码樱花 | 人妻丰满熟妇AV无码区动漫 | 羞羞视频在线观看 | 国产亚洲一区精品 | 最近免费日本视频在线 | www.youjizz.com久久| caoporn超碰最新公开 | 在线麻豆视频 | 一区网| 两个人在线观看WWW视频 | 97国产在线看片免费人成视频 |