亚洲色偷偷综合亚洲AV伊人蜜桃_最近免费看av_国产人妻午夜在线无码_国语FREE性XXXXXHD_高清做爰免费无遮网站挡_国产精品呻吟AV久久高潮

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tension cylinder Sold to France

Release time:2023-11-20 09:49:09 Hits: Current position: Home > News

This article mainly introduces:

France hydraulic cylinder,tension cylinder manufacturer,tension cylinder

France tension cylinder

(France tension cylinder,produced by Hebei Hengyu company)

tension cylinder are widely used in France,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed tension cylinder for customers from France.

Introduction to tension cylinder:

The assembly work of the tension cylinder has a great impact on the quality of the tension cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

If the tension cylinder piston rod is found to be worn, it can be brushed and plated first, then ground, and finally adjust the mating accuracy of the piston rod and the guide sleeve. At this time, the guide sleeve can be properly redrilled or the guide sleeve can be re-turned. When making the above repairs, remember to replace various rubber seals in time.

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the tension cylinder is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

The repair method of tension cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

Answers to some questions about tension cylinder:

How big is the motor and oil pump for the 80 cylinder?
Pump motor selection is not only related to cylinder diameter but also speed system, it is recommended to provide system diagram and speed requirements, generally speaking, most of the 80 cylinder on the market is equipped with 3-4KW motor, 10-20 oil pump.

What are the reasons why the hydraulic cylinder action is slower than normal?
There are many factors that cause this problem. First, measure the pressure of the main system to see whether the pressure of the main system under the pressure state is consistent with the initial setting. Before measuring the pressure, it is best to check the hydraulic oil and suction oil filter and replace or clean it. Second, check the main relief valve of the reversing control multiway valve to see if there is damage or foreign matter blocking, and clean it. If your pump is a gear pump, the problem should generally be small. Second, look at traffic. There is no leakage in the cylinder, leakage in the reversing valve spool and so on.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
主站蜘蛛池模板: 国产精品天干天干综合网 | 中文字幕1级精品视频在线 天堂爱爱 | 一个人免费视频观看在线www | 天天躁夜夜躁狠狠久久成人网 | 少妇被猛烈进入A片 | 国产成人无码精品一区不卡 | 亚洲一线产区二线产区区别在 | 无遮掩无码h成人av动漫 | 一区一区三区产品乱码 | 揉着我的奶从后面进去视频 | 国产AV无码专区亚洲A∨毛片 | 国产高清吹潮免费视频 | 亚洲精品国产第一区第二区 | 亚洲精品不卡无码福利在线观看 | 亚洲VA成无码人在线观看 | 色五月五月丁香亚洲综合网 | 最新国产精品拍自在线观看 | 亚州毛多水多久久 | 亚洲成AV人片在线观看无线 | 国产精品久久久久永久免费看 | 无码国产偷倩在线播放 | 少妇人妻88久久中文字幕 | 国产黄色麻豆视频 | 日韩久久久久久中文人妻 | 精品少妇爆乳无码av无码专区 | 2019一級特黃色毛片免費看 | 国产精品久久偷人妻 | 中文字国产精久久无 | 女人高潮被爽到呻吟在线观看 | 日韩一区二区三区四区区区 | 国产熟妇精品高潮一区二区三区 | 99精品热在线在线观看视频 | 久久久精品亚洲 | 久久久噜噜噜久久熟女 | 日韩人妻少妇一区二区三区 | GV在线网站 | 青青草在线视频网站 | 国产成人免费无码AV在线播放 | 夜色资源站www国产在线视频 | 影音先锋AⅤ天堂资源站 | 中文字幕男人天堂 |