亚洲色偷偷综合亚洲AV伊人蜜桃_最近免费看av_国产人妻午夜在线无码_国语FREE性XXXXXHD_高清做爰免费无遮网站挡_国产精品呻吟AV久久高潮

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

roller press hydraulic cylinder Sold to Angola

Release time:2023-11-24 08:39:40 Hits: Current position: Home > News

This article mainly introduces:

Angola hydraulic cylinder,roller press hydraulic cylinder manufacturer,roller press hydraulic cylinder

Angola roller press hydraulic cylinder

(Angola roller press hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

roller press hydraulic cylinder are widely used in Angola,because of long service life,smooth movement,high work efficiency.So our company has designed roller press hydraulic cylinder for customers from Angola.

Introduction to roller press hydraulic cylinder:

In recent years, the processing process of the roller press hydraulic cylinder generally adopts the rolling method, which is a pressure finishing processing, which uses the cold plastic characteristics of the metal at room temperature, and uses the rolling tool to exert a certain pressure on the surface of the workpiece, so that the surface metal of the workpiece produces plastic flow, and fills in the low concave trough of the original residue, and the roughness value of the workpiece surface is reduced. Due to the plastic deformation of the rolled surface metal, the surface tissue is cold hardened and the grain is fine, forming a dense fiber, and forming a residual stress layer, and the hardness and strength are increased, thus improving the wear resistance, corrosion resistance and compatibility of the workpiece surface. Rolling is a plastic machining method without cutting.

Do not regularly check the damage of the chrome layer of the roller press hydraulic cylinder: completely extend the roller press hydraulic cylinder and carefully check whether there is any surface damage such as injury, strain, welding slag, such as the surface damage position, in the roller press hydraulic cylinder block < 20cm, and the damage depth < 5mm, should be repaired in time to prevent long-term damage to the roller press hydraulic cylinder seal. Welding slag is strictly prohibited on the surface of the roller press hydraulic cylinder.

The difference between the integral roller press hydraulic cylinder and the split roller press hydraulic cylinder: The integral roller press hydraulic cylinder and the split roller press hydraulic cylinder in the roller press hydraulic cylinder are two different roller press hydraulic cylinders, and they are very different. The whole roller press hydraulic cylinder, which is cast in one body, is not prone to problems such as oil leakage; The split roller press hydraulic cylinder is welded twice, so if it is not handled well at the welding, it is prone to problems such as oil leakage and roller press hydraulic cylinder damage. Therefore, it is obvious that the answer to this question is for difference.

When the roller press hydraulic cylinder is installed, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the roller press hydraulic cylinder head, earring (or middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent rigid interference and cause unnecessary damage.

Answers to some questions about roller press hydraulic cylinder:

Can the hydraulic oil in the cylinder return to the tank?
Yes, there is a way, for example, first remove the cylinder from the machine, and then connect the two pipes on the cylinder, so that the cylinder piston rod is completely retracted into the cylinder, at this time, the piston is with the bottom, and the rear chamber is almost no oil, and then screw off the joint at the end of the front chamber by the hydraulic station, and put it in an empty bucket. Finally, insert the gas pipe into the oil port of the rear chamber. Open the air source, and then the rod will run out, and you'll drain the hydraulic oil from the end of the rod, which requires a source of air on site.

How to distinguish the bucket cylinder from the bucket rod cylinder?
It can be distinguished according to its installation and connection: one end of the bucket cylinder is connected with the bucket; The rod cylinder is not connected to the bucket. The bucket refers to the bucket installed on the excavator. According to the working mode, it is divided into backhoe bucket and shovel bucket, the backhoe bucket is commonly used. The boom and bucket rod are working device of the excavator, usually called the big arm and the forearm, which are mainly used to control the digging and loading of the bucket. The arm connected to the frame is longer, so it is commonly known as the big arm, and its term is called the boom. The arms connected to the digging bucket are smaller, so they are commonly known as the lower arms, and the term is called the bucket rod, so they are commonly known as the big lower arms.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
主站蜘蛛池模板: 成人免费视频国产免费麻豆 | 少妇被粗大的猛烈进出免费视频 | 亚洲a∨成熟国产一区二区成熟一级毛片 | 无码AV中文一二三区 | 久久精品女同亚洲女同13 | 内射极品少妇一区二区AV | 日本一卡2卡3卡4卡5卡精品视频 | 亚洲中文在线精品国产 | 一区一区三区产品乱码亚洲 | 東热精品中字久久无码五月天 | 久久久久久久久免费看无码 | 亚洲国产人成自久久国产 | 人人爽久久涩噜噜噜av | 日本高清视频色欧www | 色88久久久久高潮综合影院 | 日本夜爽爽一区二区三区 | 天堂va欧美ⅴa亚洲va | 国产精口品美女乱子伦高潮 | 国产v亚洲v天堂无码 | 亚洲精品TV久久久久久久久J | 久久五月丁香激情综合 | 国产黄色自拍视频 | 最近免费韩国日本HD中文字幕 | 日韩人妻无码精品专区综合网 | 中国chinese4p交换video | 国产乱人偷精品视频 | 亚洲中文久久精品无码1 | 欧美乱妇无乱码大黄a片 | 中文字幕亚洲色妞精品天堂 | 真实国产乱子伦精品一区二区三区 | 无码AV久久久久久久久 | 久久久久亚洲精品无码网址 | 国产女主播喷水视频在线观看 | 亚洲日韩看片无码超清 | 美女扒开腿让男人桶爽揉 | 国产日产精品_国产精品毛片 | 四虎WWW成人影院 | 国产女主播喷水视频在线观看 | 久久伊人成色777综合网 | 国产精品黄页免费高清在线观看 | 三级全黄的视频在线观看 |