亚洲色偷偷综合亚洲AV伊人蜜桃_最近免费看av_国产人妻午夜在线无码_国语FREE性XXXXXHD_高清做爰免费无遮网站挡_国产精品呻吟AV久久高潮

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stacker cylinder Sold to Pakistan

Release time:2023-12-18 10:57:10 Hits:126 Current position: Home > News

This article mainly introduces:

Pakistan hydraulic cylinder,stacker cylinder manufacturer,stacker cylinder

Pakistan stacker cylinder

(Pakistan stacker cylinder,produced by Hengyu Hydraulic Cylinder Factory)

stacker cylinder are widely used in Pakistan,because of clever hydraulic energy conversion,no transmission clearance,powerful torque.So our company has designed stacker cylinder for customers from Pakistan.

Introduction to stacker cylinder:

How to repair the stacker cylinder body when it is damaged: When the stacker cylinder has trace deformation and shallow tensile marks, the stacker cylinder is repaired by strong honing process. The heavy honing process can repair stacker cylinders up to 2.5 times out of tolerance than the original tolerance. It honed the parts with excessive size or shape error through a powerful honing machine, so that the overall size, shape tolerance and roughness of the stacker cylinder can meet the technical requirements.

The assembly work of the stacker cylinder has a great impact on the quality of the stacker cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

There are some honeycomb holes in the inner wall of the stacker cylinder, piston or piston rod surface. How is this formed? When we repair the stacker cylinder, we can see that there are some honeycomb holes on the inner wall of the stacker cylinder, the piston or the piston rod surface, which are caused by cavitation. Therefore, the cavitation of the stacker cylinder is targeted to prevent. Is very necessary.

Do not enter foreign bodies when installing the stacker cylinder block. The place where the installation operation is carried out, the conditions are not good, and foreign bodies can be entered unconsciously. Therefore, the installation site must be cleaned up around, especially the place where the parts are placed must be cleaned, so that there is no dirt.

Answers to some questions about stacker cylinder:

How to set up the one-way cylinder hydraulic system?
Single acting oil cylinder, that is, an oil cylinder with an oil port, can use two three-way valves to control the cylinder action. The three oil ports are respectively connected to P (oil pump), A (oil cylinder), and T (oil tank). If the oil pump is to run continuously, an electromagnetic relief valve can be added. When the cylinder is not moving, the relief valve can unload the oil pump. You can also add a three-way four-way valve, the middle function is unloaded, two outlets: A connected to the fuel tank, B connected to the cylinder.

Two cylinders have a reversing control, if the load of the two cylinders is not the same, how to ensure their synchronization?
The piston rod of the cylinder is required to extend synchronization: install A shunt collector valve or synchronous motor at port A of the direction control valve, and then connect the two outlets of the shunt collector valve to the rod-free cavity of the two cylinders respectively. It is required that the outlet of the diverter collector valve is connected to the rod cavity of the two cylinders respectively when the piston rod is withdrawn in synchronization. The synchronization performance depends on the quality of the diverter valve and the leakage of the hydraulic system.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
主站蜘蛛池模板: 亚洲欧美日韩中文二区 | 成人影片麻豆国产影片免费观看 | 国产亚洲AV综合人人澡精品 | 欧美性色黄大片WWW喷水 | 人人狠狠综合久久88成人 | 久久精品无码AV | 太深太粗太爽太猛了视频免费观看 | AV在线观看网站无码不卡的 | 中文字日产幕码三区的做法大全 | 99国产精品久久99久久久 | 黄色片子在线观看 | 把极品白丝班长啪到腿软 | 99亚洲乱人伦aⅴ精品 | 少妇被粗大的猛烈进出动态图片 | 故意短裙公车被强好爽在线播放 | 在线免费高清一区二区三区 | 欧美最猛性xxxxx大叫 | 久久久久国产精品人妻 | 美美女高清毛片视频免费观看 | 日韩经典一区二区三区 | 亚洲国产av无码精品无广告 | 亚洲中文字幕无码永久免弗 | 国产精品久久人妻无码HD毛片 | 六月丁香婷婷色狠狠久久 | 亚洲日韩看片无码超清 | 欧美成人aaaaa片 | 午夜亚洲人人精品一区 | 爆乳少妇在办公室在线观看 | 国产精品欧美亚洲韩国日本久久 | 成人免费播放视频777777 | 亚洲人片在线观看天堂无码 | 欧美精品成人影院 | 精品无码AV在线观看 | 欧美丰满少妇XXXX性 | 又爽又黄又无遮挡网站动态图 | 少妇午夜性影院私人影院成都 | 爱爱免费视频网站 | 精品无人区麻豆乱码1区2区 | 久久精品国产免费观看三人同眠 | 狠狠躁夜夜躁人人爽天天古典 | 性欧美XXXXX极品少妇 |