亚洲色偷偷综合亚洲AV伊人蜜桃_最近免费看av_国产人妻午夜在线无码_国语FREE性XXXXXHD_高清做爰免费无遮网站挡_国产精品呻吟AV久久高潮

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

push and pull the cylinder Sold to New Zealand

Release time:2023-12-21 12:32:49 Hits: Current position: Home > News

This article mainly introduces:

New Zealand hydraulic cylinder,push and pull the cylinder manufacturer,push and pull the cylinder

New Zealand push and pull the cylinder

(New Zealand push and pull the cylinder,produced by Hebei Hengyu company)

push and pull the cylinder are widely used in New Zealand,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed push and pull the cylinder for customers from New Zealand.

Introduction to push and pull the cylinder:

The push and pull the cylinder should be used as far as possible to avoid the transverse force, sometimes the piston rod to bear the transverse load is too large, especially do not force or pull the push and pull the cylinder, bite. Elimination method: When installing the push and pull the cylinder, ensure that the axis position of the push and pull the cylinder is consistent with the direction of movement; Make the load borne by the push and pull the cylinder as far as possible through the push and pull the cylinder axis, to avoid the phenomenon of eccentricity.

The piston rod and guide sleeve function of the push and pull the cylinder is crucial: the relative motion pair between the piston rod and the guide sleeve is the main factor causing external leakage, if the chrome layer on the surface of the piston rod is spalling or producing longitudinal tensile marks due to wear, it will directly lead to the failure of the seal.

When the push and pull the cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the push and pull the cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil push and pull the cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical push and pull the cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the push and pull the cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

The push and pull the cylinder should be avoided for a long time without use, if it is indeed idle for a long time for some reason, it should also be regularly turned on for empty operation, so that its parts can be fully lubricated, so as to avoid rust on the working surface and affect the normal work in the future. (If it cannot be turned on and run, a small amount of lubricating oil can be applied on its outer surface for protection) ' The use of the push and pull the cylinder should pay attention to: the operation should be as far away from the push and pull the cylinder as possible, to avoid falling objects, knocking, rubbing the push and pull the cylinder coating. When cleaning the push and pull the cylinder, only use soft materials (such as cotton) to wipe, and do not scratch high-hardness materials. Do not use the push and pull the cylinder when the oil temperature exceeds 70 ° C.

Answers to some questions about push and pull the cylinder:

What is the cause of the deep scratch of the cylinder?
The following reasons can cause the cylinder to be scratched. 1: Hydraulic oil containing particulate impurities into the hydraulic cylinder, these particulate impurities stuck between the piston rod and the guide ring (or stuck between the piston and the inner wall of the cylinder), when the piston movement in the cylinder will scratch the piston rod, the phenomenon of the inner wall of the cylinder, the more particles, the larger the scratch marks the deeper and more obvious. 2: The body of the cylinder itself. Due to assembly or design reasons, the coaxial error between the piston rod, piston, cylinder, guide ring and other parts is too large, or the cylinder, piston rod straightness error is too large, so that the piston rod and the guide ring interference between the cylinder, this mechanical interference will certainly lose the piston rod or cylinder wall.

The difference between the overall cylinder and the separate cylinder of the truck?
The whole cylinder is cast in one piece, and such a cylinder generally does not leak oil. Split cylinder refers to two welded, easy to leak oil in the welding place, resulting in damage to the cylinder, or its body can not get up, many people do not use this kind of cylinder now.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
主站蜘蛛池模板: 夜先锋av资源网站 | 狠狠躁夜夜躁AV网站中文字幕 | 亚洲国产精品无码AV久久久 | 狠狠色噜噜狠狠狠狠色综合网 | 色婷婷婷亚洲综合丁香五月 | 精品国产乱码久久久久久软件大全 | av边做边流奶水无码免费 | 老师在办公室被躁在线观看 | 99久久国产综合精品SWAG | 婷婷五月综合人人网 | 美丽人妻在夫前被黑人 | 女性自慰网站免费看WW | 内地老太婆内射内地小矮人内射 | 欧美日韩综合一区二区三区 | 久久久视频在线观看 | 日本阿V网站在线观看中文 欧美深夜影院 | 国产手机在线精品 | x8x8拨牐拨牐x8免费视频8文字 | 欧美人与物ⅴideos另类 | 亚洲精品国产一区二区色欲影院 | 国产亚洲精品AE86 | 麻豆人妻少妇精品无码专区 | 国产十八禁真成了 | 欧美猛男军人gay巨大 | 久久熟妇人妻午夜寂寞影院 | 精品无码久久久久国产手机版 | 日韩欧美一区二区三区在线视频 | 国产无遮挡又爽又黄大胸免费 | 亚洲男人的天堂在线aⅴ视频 | 一二三四社区在线中文视频 | 日本r级在线 | 亚洲一区二区三区无码久久 | 国产第一页浮力影院入口 | 提莫影院AV毛片入口 | 人妻少妇精品系列 | 亚洲人成网站在线播放2019 | 丰满人妻被黑人猛烈进入 | 最好看的2018中文在线观看 | 无码成人午夜福利视频 | 精品无码国产污污污免费网站国产 | 无码精品人妻一区二区三刘亦菲 |