亚洲色偷偷综合亚洲AV伊人蜜桃_最近免费看av_国产人妻午夜在线无码_国语FREE性XXXXXHD_高清做爰免费无遮网站挡_国产精品呻吟AV久久高潮

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

pusher hydraulic cylinder Sold to Luxembourg

Release time:2024-01-05 16:43:22 Hits: Current position: Home > News

This article mainly introduces:

Luxembourg hydraulic cylinder,pusher hydraulic cylinder manufacturer,pusher hydraulic cylinder

Luxembourg pusher hydraulic cylinder

(Luxembourg pusher hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

pusher hydraulic cylinder are widely used in Luxembourg,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed pusher hydraulic cylinder for customers from Luxembourg.

Introduction to pusher hydraulic cylinder:

The definition of the minimum stable speed refers to the minimum movement speed of the pusher hydraulic cylinder without crawling phenomenon when the full load is moving, it has no uniform indicator, and the pusher hydraulic cylinder that undertakes different work has different requirements for the minimum stable speed.

After chrome plating of the piston rod of the pusher hydraulic cylinder, the surface flatness is not fully treated: After chrome plating of the piston rod surface, the method of post-plating polishing should be changed to post-plating polishing. Although it is necessary to increase the thickness of the coating before grinding (generally increased by about 0.02 in the diameter direction), it can remove chrome plating defects well, and test the binding force of the coating. In addition, due to the micro-roughness of the grinding surface, the trough can store lubricating oil, which can improve the wear resistance and extend the service life.

Because of the slightly complex structure of the buffer pusher hydraulic cylinder, sometimes there will be problems, such as when the pusher hydraulic cylinder with the buffer device is started in reverse, the piston often stops temporarily or reverses. Elimination method: The orifice of the check valve is too small, so that the amount of oil entering the buffer chamber is too small, and even a vacuum occurs, so the above fault phenomenon will occur when the buffer plunger leaves the end cover. In this regard, the orifice of the check valve should be increased.

In the process of using the pusher hydraulic cylinder, sometimes such a problem will occur, the pusher hydraulic cylinder can not act immediately after the instruction of the pusher hydraulic cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil pusher hydraulic cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

Answers to some questions about pusher hydraulic cylinder:

What are the causes of hydraulic cylinder oil leakage?
First, between the piston rod and the guide sleeve: 1, the cylinder force is not good, there is a radial force between the piston rod and the guide sleeve there is a partial load, so that the oil seal is worn early, causing oil leakage. 2. The ambient temperature of the piston rod is high, especially radiant heat, and the oil seal aging is fast. 3. Whether the oil seal is selected correctly; Check whether the oil seal is damaged during installation. 4, guide sleeve and piston rod matching tolerance is correct. Second, between guide sleeve and cylinder: 1. Whether the O-ring on the guide sleeve is installed correctly, pay special attention to the O-ring can not "roll", especially some O-rings are die-pressed with a die-closing line. Third, common problems: 1, guide sleeve, cylinder, piston rod concentricity is poor. Fit tolerance is correct.

Why should the piston rod of the hydraulic cylinder be so precise? If you hope the cylinder has a long service cycle, then all parts need to be high-precision, not only the piston rod, but also the cylinder, the sealing groove, the surface roughness, the cylinder looks very simple. Any hydraulic factory can produce the cylinder, but the good cylinder is difficult to produce.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
主站蜘蛛池模板: 久久AⅤ无码精品色午麻豆 又粗又大又硬毛片免费看 亚洲成在人线综合导航 | 色欲色香天天天综合网WWW | 久久久久久自慰出白浆 | 美美女高清毛片视频免费观看 | 7878成人国产在线观看 | 插我一区二区在线观看 | 国产一线二线三线女 | 国产无人区码一码二码三MBA | 奇米影视7777狠狠狠狠色 | 蜜桃视频在线观看免费网址入口 | 精品久久久无码中文字幕边打电话 | 日出水了特别黄的视频 | 欧美老人与小伙子性生交 | 久久精品国产只有精品2020 | 无码人妻精品一区二区蜜桃百度 | 国产精品国产三级国产专区53 | 中文日产幕无线码一二 | 肥大bbwbbw的高潮 | 蜜桃成人无码区免费视频网站 | 在线天堂资源www在线中文 | 人妻熟女视频一区二二区 | 久久久久无码国产精品不卡 | 天噜啦精品免费视频日本免费视频 | 91大神一区二区三区 | 午夜亚洲国产理论片二级港台二级 | 人妻熟女一二三区夜夜爱 | 2020年最新国产精品正在播放 | 亚洲欧洲日本无在线码 | 18禁动漫美女禁处被爆桶出水 | 激烈的性高湖波多野结衣 | 曰韩无码AV一区二区免费 | 最近中文字幕高清中文字幕无 | 国产成人精品综合在线观看 | 久久人妻无码一区二区三区AV | 国产在线视频www色 幻女bbwxxxx | 久久精品亚洲成在人线av麻豆 | 玩弄邻居少妇高潮潮喷的经历 | 人人妻在人人 | 9999国产精品欧美久久久久久 | 亚洲中文字幕无码专区 | 国产成人精品日本亚洲专区 |